Updated November 2026

Learning how to cut landscape edging means trimming the lawn’s border so the grass, mulch and bed lines stay sharp and level. With the right tool and a steady hand, you can cut most types of edging in a single afternoon. The process works the same for plastic, steel and stone, though the blade or cutter you use will change.

Choose the Right Tool for Your Edging Material

The tool you pick depends on what the edging is made of. Thin plastic and aluminum edging can be trimmed with a string trimmer held at an angle, while steel and thick plastic need a hacksaw, a metal-cutting blade or a rotary tool. Stone and concrete edging generally can’t be cut at all, so you’ll be trimming the grass beside it instead.

Shopping for one? See our guide: 6 Best Easyflex No Dig Landscape Edging Kit Options for Clean Lines (2026).

Before you start, check whether the edging is a single strip or a segmented product. Segmented edging can often be snapped or cut at the joint, which saves a lot of effort.

Step-by-Step: Cutting Landscape Edging

  1. Mark the cut line with a permanent marker or a piece of painter’s tape. Mark the spot about 1/8 inch past the point you want to remove, so you have room to file the end smooth.
  2. Support the edging on both sides of the cut. Use a brick or a short board so the strip doesn’t flex and pinch the blade.
  3. Score the metal or plastic first. Run a hacksaw or cutting disc along the line with light, even strokes. Forcing the cut can bend the strip or crack plastic.
  4. Finish the cut. Once you’ve cut most of the way through, snap the remaining piece by hand or make a clean final pass.
  5. Smooth the end. Run a metal file or sandpaper over the cut edge to remove burrs, which can snag shoes and mower wheels.
  6. Test the fit. Set the piece back into the trench and check that the top sits level with the surrounding grade.

Cutting Steel and Aluminum Edging

Metal edging produces sharp burrs and hot shavings, so wear gloves and eye protection. A fine-tooth hacksaw blade (around 24 teeth per inch) gives a cleaner cut than a coarse one. Keep the blade moving steadily and avoid rushing, since heat can dull the teeth.

Cutting Plastic Edging

Plastic is easier to cut but can crack if the blade binds. A utility knife works on thinner strips, and a fine-tooth saw handles thicker profiles. Mark your line and cut slowly, letting the tool do the work.

Where to Cut for Clean Lines

Cutting at the right spot matters as much as the tool. Make your cut so the top edge sits flush with the soil or mulch, not so high that it sticks up and catches the mower deck. Most homeowners aim for the edging to sit about 1 inch above the grade on lawn-side borders, though manufacturers’ install guides may specify something slightly different for their product.

Edging Material Best Cutting Method Blade or Tool
Plastic (thin) Score and snap, or straight cut Utility knife or fine saw
Plastic (thick) Slow saw cut Fine-tooth hand saw
Aluminum or steel Hacksaw or cutoff tool Fine-tooth metal blade
Stone or concrete Do not cut; trim adjacent grass String trimmer or edger

Common Mistakes to Avoid

  • Cutting without support, which bends the strip and leaves a crooked end.
  • Using a coarse blade on metal, which tears the edge instead of cutting cleanly.
  • Skipping the file step, leaving sharp burrs that can injure hands or puncture tires.
  • Cutting too close to the final mark, leaving no room for a smooth finish.
  • Forgetting that you can cut the grass line with a string trimmer rather than cutting the edging itself.

If you’re still deciding how the border should look before you cut, the guide on How to Install Landscape Edging: A Step-by-Step Guide for Clean Borders covers layout and depth. For metal strips specifically, How to Cut Metal Landscape Edging Cleanly: A Step-by-Step Guide goes deeper into blade choice and finishing.

  • Fine-tooth hacksaw: a cleaner, more controlled cut on steel and aluminum than a coarse blade. View on Amazon
  • Metal file: removes burrs from cut ends so they don’t snag shoes or equipment. View on Amazon
  • Cut-resistant work gloves: protect your hands from sharp edges during handling and cutting. View on Amazon

FAQ

Can I cut landscape edging with a string trimmer?

A string trimmer can’t cut through metal or plastic edging reliably. It works well for trimming the grass alongside the edging, which is the more common job.

Should I cut edging before or after installing it?

Cut it before installation whenever possible. Trimming pieces on a flat surface gives you better control and a straighter end.

How do I keep a cut edge from rusting?

File away the burrs and apply a light coat of rust-inhibiting paint to bare steel ends. This is especially useful for galvanized or steel strips exposed to moisture.

Conclusion

To cut landscape edging cleanly, match the tool to the material, support the strip, and cut with steady, even strokes. Finish each end with a file so it’s safe to handle and sits flush in the trench. With those habits, your borders will look sharp for seasons to come.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our lawn edging & trimming guides, checking product details against manufacturer specifications and owner feedback.