Updated November 2026
DIY landscape edging concrete is one of the most durable ways to define a flower bed, walkway, or lawn border. With basic forms, a bag of concrete mix, and a few hours of work, you can pour a crisp edge that holds its shape for years. This guide covers the layout, forming, pouring, and finishing steps so your edge comes out level and clean.
Plan the Layout and Gather Supplies
Mark the edge with a garden hose or spray paint before you dig. Curves should be smooth arcs, and straight runs should be checked with a string line. A common profile is 4 to 6 inches wide and 3 to 4 inches deep above grade, with a 6-inch trench below the soil line for stability.
Shopping for one? See our guide: 7 Best Concrete Landscape Edging Machine Options for Clean Lines (2026).
Gather your materials before mixing anything. You will need:
- Pre-mixed concrete (a 60 lb bag yields roughly 0.45 cubic feet)
- Lumber or plastic forms, 2×4 or 2×6 boards, or flexible edging forms
- Stakes, 1-inch wood screws, and a drill
- Shovel, tamper, trowel, edger tool, and a level
- Gravel base (about 2 inches) and a plastic sheet if soil is wet
- Wire mesh or rebar for longer runs
Dig the Trench and Build the Forms
Dig the trench to the depth of your profile plus 2 inches for a gravel base. Compact the bottom with a hand tamper, then add and tamp the gravel. This base reduces cracking caused by frost heave and soil settling.
Set your forms along the layout line, staking them every 18 to 24 inches. Brace the top edge level with a level tool and check that the form tops match your intended grade. For curves, use flexible plastic forms or bend thin plywood strips around stakes.
Add Reinforcement
Place wire mesh or a single length of rebar about 1.5 inches above the base in longer runs. Keep reinforcement off the form walls so it sits inside the concrete.
Mix, Pour, and Finish the Concrete
Mix the concrete to a stiff, workable consistency, similar to thick peanut butter. Too much water weakens the edge and causes surface cracking. Pour in sections, pushing the mix into corners and removing air pockets by tapping the form sides or working the mix with a trowel.
Screed the top flush with the form edges, then wait until the surface loses its sheen before finishing. Use an edger tool to round the top corners, and a float for a smooth surface. For a broom texture, drag a stiff broom lightly across the top once the surface has firmed.
Cure Properly
Keep the concrete damp for at least three days by misting it lightly or covering it with plastic. Avoid pouring in temperatures below about 40°F or in direct heat above 90°F. Remove forms after 24 to 48 hours, once the edge holds its shape without slumping.
Common Mistakes
- Skipping the gravel base, which leads to heaving and cracks within the first winter.
- Adding too much water to make the mix easier to pour.
- Pouring over soil that has not been compacted.
- Removing forms too early and damaging the edges.
- Failing to cut control joints, which lets random cracks form.
Recommended Gear
- Concrete edger tool: rounds the top corners cleanly for a finished look. View on Amazon
- Magnesium float: smooths the surface without bringing excess water to the top. View on Amazon
- Flexible plastic edging forms: make curved runs easier to shape and reuse. View on Amazon
If you want more options for materials and styles, see Poured Concrete Landscape Edging: A Step-by-Step Guide for Clean Lines and Concrete Block Landscape Edging: A Step-by-Step Guide (2026).
FAQ
How deep should DIY concrete landscape edging be?
Most homeowners pour edging 3 to 4 inches above grade, with a 6-inch trench below for stability. Deeper footings help in areas with frost or soft soil.
Can I pour concrete edging without forms?
You can shape edging by hand using a trench as a mold, but forms give cleaner, more consistent lines. Flexible forms are a good middle option for curves.
How long before I can mow over new concrete edging?
Wait at least 7 days before driving or mowing over the edge, and up to 28 days for full strength. Light foot traffic is usually fine after 48 hours.
Conclusion
A well-prepared base, a stiff mix, and proper curing are what separate lasting concrete edging from a cracked mess. Plan your layout carefully and take the time to compact and cure. With these steps, you can build a clean, durable border that frames your landscape for years.
