Updated November 2026
Black and Decker weed eater string is the cutting line that spins at the head of your trimmer, and choosing the right diameter and style keeps your edges clean and your motor working well. This guide explains how to identify the correct line for your model, how to load it, and what to watch for so you spend less time stopping to refeed.
Identify the Right String for Your Trimmer
Before buying any weed eater string for Black and Decker equipment, check the diameter printed on your spool cover, the owner’s manual, or the label inside the head. Most consumer models take line between about 0.065 and 0.095 inches, and manufacturers specify the approved size for each model. Using line that is too thick can overload the motor, while line that is too thin wears out quickly and may not cut tall grass.
Shopping for one? See our guide: 6 Best Weed Eater Gas Leaf Blower Combos for Yard Care (2026).
Also note the head type. Some heads use a bump-feed mechanism, while others require you to pull line out by hand and wind it onto a spool. The head type determines whether you can use pre-cut line or need a continuous coil.
Load or Replace the String
Replacing line on a typical black and decker weed eater string head takes only a few minutes. Work through these steps:
- Unplug the trimmer or remove the battery, and set it on a flat surface.
- Press the tabs on the spool cover or twist it counterclockwise to remove it.
- Remove the old spool and any remaining line.
- Cut a length of new line as the manufacturer specifies, often roughly 15 to 20 feet for a full spool.
- Fold the line at its midpoint and insert it into the eyelet on the spool, leaving equal lengths on each side.
- Wind the line onto the spool in the direction marked by the arrow, keeping the coil tight and even.
- Feed the ends through the outlet holes on the head, pull a few inches of each end out, and reinstall the spool cover.
Feed Line Correctly and Avoid Jams
Uneven winding is the most common reason line fails to feed. If the coil bunches or overlaps, the spool can seize, so wind slowly and keep tension consistent. After reinstalling the cover, tap the head on the ground with the trimmer running briefly to see whether line advances. If it does not, open the head and check for tangles.
| Symptom | Likely cause | Fix |
|---|---|---|
| Line won’t feed | Spool wound unevenly or overloaded | Rewind with even tension and less line |
| Line breaks quickly | Line too thin or cutting hard material | Use the specified diameter; avoid hitting fences and stones |
| Head vibrates | Line unevenly loaded on the spool | Rewind so both sides are balanced |
Common Mistakes and Tips
- Using line thicker than the manufacturer specifies, which strains the motor.
- Winding the spool in the wrong direction, which prevents smooth feeding.
- Leaving the trimmer running with no line loaded, which can damage the head.
- Cutting line on a hot engine or motor housing, which can warp it.
- Storing spare line in direct sunlight, which makes it brittle.
If your head is damaged or the cord is faulty, repair the part before adding new line. For cord problems, see Black and Decker Weed Eater Cord: How to Replace or Fix a Damaged Cord. If you own a battery model, Ryobi Battery Powered Weed Eater: Setup, Use and Tips for Clean Trims covers similar head-loading steps for cordless trimmers.
Recommended gear
A spool winder helps keep line even when you load a fresh spool, which reduces feeding problems. View on Amazon
Replacement spools sized for your model save time when you are not sure how much line to cut. View on Amazon
Line cutters with a sharp, clean blade make it easier to trim line to an even length. View on Amazon
FAQ
What diameter of weed eater string does Black and Decker use?
It depends on the model. Check the spool cover, label or owner’s manual for the approved diameter, and do not exceed it.
Why does my black and decker weed eater string keep breaking?
Line that is too thin, cutting into fences or stones, or running the trimmer at full speed in dense growth are the usual causes. Matching the diameter to your model and cutting with the tip of the line helps.
Can I use any brand of trimmer line on my trimmer?
You can use other brands if the diameter and head type match your trimmer. Confirm the size with the manufacturer or a qualified repair shop if you are unsure.
Conclusion
Choosing the correct black and decker weed eater string, winding it evenly, and checking the head regularly will keep your trimmer cutting cleanly. Start by confirming your model’s diameter, then follow the loading steps above. Consult your owner’s manual or a repair professional for any issues with the motor or head.
