Updated November 2026
Replacing a Stihl weed eater head takes about ten minutes once you know which head you have and how it attaches. This guide walks through identifying your trimmer head, removing the old one, and installing a replacement so it spins true and feeds line correctly. Most of the work is matching the right head to your shaft and making sure the bump knob and retaining parts are seated properly.
Identify Your Stihl Trimmer Head Type
Stihl uses several trimmer head designs, and a head that fits one shaft or model may not fit another. Before buying anything, check the model number on your trimmer and the head currently installed. Look for the part number stamped on the head or printed on the packaging of the old one. If the head is worn or cracked and you can’t read any markings, measure the thread diameter on the drive shaft and note whether the head uses a bump-feed knob, a fixed line, or a metal blade attachment.
Shopping for one? See our guide: 3 Best Stihl Weed Eater Wire Heads for Clean Trimming (2026).
Manufacturers specify compatible heads by model, so confirm the fit with the official Stihl parts list for your trimmer before ordering. Owners often report that a head looks similar to the old one but has different threading or a different number of line ports.
Remove the Old Trimmer Head
Stop the engine or disconnect the battery and wait for the shaft to stop moving completely. Then work through these steps:
- Place the trimmer on a flat surface with the head facing up.
- Hold the drive shaft still with a spanner or by locking the shaft with the tool your model provides.
- Turn the head counterclockwise to unscrew it. Some heads use a reverse thread, so if it doesn’t loosen, try turning it the opposite way.
- Lift the head off and set aside any retaining springs, washers, or spool components.
- Clean the shaft threads with a rag and check for grass or debris packed behind the head.
Install the New Head Correctly
Preparation matters more than force. Cross-thread a head and you can damage both the head and the shaft. Start the new head by hand, turning it slowly until it seats. Then tighten it firmly, but not so hard that you strip the threads.
- Confirm the spring and retaining parts are installed in the same order as the old head.
- Thread the new head clockwise by hand until it stops.
- Lock the shaft and tighten with the tool, bringing it snug without overtightening.
- Spin the head by hand. It should turn freely with no wobble or grinding.
- Load line according to the manufacturer’s instructions for your head type.
Test the Head Before Trimming
Run the trimmer at low throttle or low battery power for about 30 seconds and watch the head. A slight wobble means the head or retaining parts are not fully seated. Stop, remove the head, and reinstall it. Once it runs smoothly, feed a short length of line and check that it extends and retracts correctly if your head uses bump feed.
Common Mistakes to Avoid
- Ordering a head by appearance instead of by model number.
- Forgetting the retaining spring or washer and assuming the head is secured.
- Running the trimmer with a loose head, which can damage the shaft bearing.
- Overtightening the head and stripping the threads.
- Skipping the test run and discovering a wobble only after trimming.
Recommended Gear
A basic spanner or shaft lock makes holding the drive shaft steady far easier than improvising with a screwdriver.
Replacement line that matches your head’s line diameter helps prevent feeding problems after installation. View on Amazon
A small set of rags or a shop towel keeps the threads clean so the new head seats properly. View on Amazon
FAQ
Can I replace a Stihl weed eater head with a generic one?
Some generic heads fit Stihl shafts, but thread size and head design vary. Check compatibility against the model number before buying, and use the official parts list as your reference.
Why does my new head wobble after installation?
Usually the head is not fully threaded or a retaining spring is missing or misplaced. Remove the head, confirm the parts are in order, and reinstall it.
Do I need to remove the shaft to replace the head?
No. In most cases you only need to lock the drive shaft and unscrew the head. If the shaft itself is damaged, consult a qualified small engine repair technician.
Conclusion
Replacing a Stihl weed eater head comes down to matching the correct part, removing the old head cleanly, and seating the new one without cross-threading. Test it at low power before trimming. Following these steps keeps your trimmer running smoothly and extends the life of the drive shaft.
Related reading
- Weed Eater Attachment for Stihl: Choose and Use the Right One (2026)
- Stihl FS 56 RC Weed Eater: Setup, Starting and Trimming Tips
- Stihl Electric Weed Eater: 3 Best Options for Clean Edges (2026)
- Stihl Blade Weed Eater Guide: Choose and Replace the Right Blade (2026)
- Echo or Stihl Weed Eater (2026): Which Is Better for Your Yard?
- Battery Stihl Weed Eater: How to Choose and Use One for Clean Edges
