Updated November 2026

A Kobalt weed eater head holds the trimmer line that does the cutting, and it wears out faster than most parts on the machine. Replacing or reloading it takes about ten minutes with basic tools. This guide shows you how to identify your head, decide whether to reload or replace it, and get the line feeding correctly so your trimmer cuts cleanly.

Identify Your Kobalt Weed Eater Head First

Before you buy anything, check what you actually have. Kobalt trimmers have used several head designs over the years, and the most common types are bump-feed heads (you tap the head on the ground to release more line) and fixed or automatic-feed heads. Look for model numbers stamped on the housing, the motor cover or the shaft. The owner’s manual lists compatible heads, and the printed label on the old head often shows the spool size and line diameter.

Shopping for one? See our guide: 3 Best Stihl Weed Eater Wire Heads for Clean Trimming (2026).

Note the diameter of the line your head takes, typically listed in the manual or on the packaging. Using line that is too thick can damage the head or overload the motor, while line that is too thin wears out quickly.

Reload the Line on a Bump-Feed Head

Reloading is the most common task and usually the quickest. Work through these steps:

  1. Disconnect the spark plug boot or remove the battery so the trimmer cannot start while you work.
  2. Press the tabs on the head cover, or remove the retaining screws, and lift off the cap.
  3. Remove the old spool and clear any broken line or debris from the chamber.
  4. Cut a length of new line to the length specified in the manual, often about 15 to 20 feet for a standard spool.
  5. Fold the line at its midpoint and wind it onto the spool in the arrow direction printed on the spool. Leave the tails in the anchor slots.
  6. Reinstall the spool, thread the tails through the eyelets, and snap the cap back on.
  7. Pull the line tails to release a few inches of trimmer line and check that both ends are even.

Replace the Entire Head When Reloading Is Not Enough

Replace the head instead of reloading when the housing is cracked, the spring is broken, the eyelets are worn smooth, or the spool no longer seats properly. A cracked housing can throw line or break apart at speed, so treat that as a safety issue. Buy a replacement head that matches your model number rather than assuming a universal fit.

To swap the head, remove the old one by unscrewing it from the shaft (turn it in the direction that loosens it, which is usually counterclockwise when facing the head). Thread the new head on by hand first to avoid cross-threading, then tighten it snugly. Do not over-tighten plastic threads.

Check Feed and Balance After Installation

Before you start cutting, confirm the head feeds freely. Hold the trimmer with the shaft horizontal, pull the line, and make sure the spool turns without catching. Run the engine or motor briefly at idle, then at a moderate speed, and watch for wobble. A head that vibrates usually means the line is wound unevenly or the cap is not fully seated.

Checklist before you trim

  • Correct head model and line diameter
  • Line wound in the arrow direction with equal tails
  • Cap snapped fully shut with no gaps
  • Spark plug boot or battery reconnected

Common Mistakes to Avoid

  • Winding line against the arrow direction, which causes tangles and poor feeding.
  • Using line thicker than the head rating, which strains the motor and can crack the housing.
  • Forgetting to disconnect power before opening the head.
  • Tightening a replacement head by force, which strips threads.
  • Ignoring a cracked or worn head, which can release line or debris at high speed.

A pair of work gloves protects your hands when handling sharp line ends and hot shafts, and a small flat screwdriver or the tool supplied with your trimmer helps with cap and screw removal. View on Amazon is a practical starting point for hand protection, and View on Amazon lets you keep a spare spool on hand so you can reload in seconds during a long job.

FAQ

How do I know which Kobalt weed eater head fits my trimmer?

Check the model number on your trimmer and the compatibility list in the owner’s manual. Matching the head to that number avoids fit and threading problems.

How much trimmer line should I load?

Follow the length and diameter in your manual, which is usually around 15 to 20 feet of line for a standard spool. Overfilling can jam the head.

Why does my head keep feeding poorly after reloading?

The most common causes are line wound against the arrow direction, uneven tails or a cap that is not fully seated. Rewind the spool and check all three.

Conclusion

Identifying your head, reloading or replacing it correctly, and checking the feed before cutting will get your Kobalt trimmer working cleanly again. Keep a spare spool ready and inspect the housing regularly for cracks. For repairs beyond the head, such as motor or shaft problems, consult a qualified small-engine or power tool technician.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our lawn edging & trimming guides, checking product details against manufacturer specifications and owner feedback.