Updated November 2026

Landscape edging for trees creates a clean, defined border around the base of a tree so mulch stays put, grass stops creeping in, and mower or trimmer blades stay clear of the trunk. Done right, the edge follows the tree’s root zone without damaging roots or girdling the trunk. This guide walks through planning the border, setting the edging, and avoiding the errors that cause problems later.

Plan the Border Around the Root Zone

Start by deciding how far the bed should extend. Most mature trees have the majority of their feeder roots in the top 12 to 18 inches of soil, spreading out to roughly the drip line, which is the outer edge of the canopy. A practical rule is to make the bed at least one-third to one-half of the distance from the trunk to the drip line, with a minimum radius of about 3 feet for small trees. Leave a mulch-free ring of 2 to 3 inches around the trunk itself so bark stays dry and pests have fewer hiding spots.

Shopping for one? See our guide: 6 Best Easyflex No Dig Landscape Edging Kit Options for Clean Lines (2026).

Mark the outline with a garden hose or spray paint. Curves should be smooth, since tight, wiggly lines are harder to keep neat and tougher to edge later. If the tree sits near a sidewalk, fence, or structure, shape the bed to follow those lines so the border reads as intentional.

Choose Edging That Suits the Site

The material should match the soil, traffic, and look you want. Flexible steel or aluminum strips handle curves well and resist root intrusion when set deep enough. Stone or paver edging gives a firm, permanent line but needs a compacted base. Pressure-treated wood works for a warmer look, though it will eventually decay, so keep it away from the trunk and check it periodically.

Edging type Best for Main consideration
Steel or aluminum strip Curves and tight lines Must be pinned or buried to stay upright
Stone or pavers Permanent, formal borders Needs a compacted gravel base
Pressure-treated wood Warm, rustic look Will decay over time
Plastic or rubber Simple, flexible installs Lighter profile, less rigid

For a deeper comparison of options, see What Are the Best Options for Landscape Edging? 7 Choices Compared. If you prefer metal, Steel Landscape Edging Nearby: How to Find the Right Option (2026) covers sourcing and sizing.

Install the Edging in Four Steps

  1. Dig a shallow trench. Cut along your marked line to a depth equal to the edging height, usually 4 to 6 inches for most strip products. Keep the trench bottom level.
  2. Set the edging. Place it in the trench with the top edge slightly above grade so mulch and soil don’t spill over. Keep the top flush or just above the lawn surface.
  3. Secure it. Drive stakes or spikes every 12 to 18 inches on the inside of the bed, with the heads below the top edge. Check that the line stays straight or curves smoothly.
  4. Backfill and mulch. Tamp soil firmly against the outside of the edging, then add 2 to 3 inches of mulch inside the bed, keeping it clear of the trunk.

Stakes and spikes are the most common holding method. Spikes for Landscape Edging: A Step-by-Step Guide to Clean Lines explains spacing and driving technique in more detail. Stone or paver borders need a different approach, which is covered in Poured Concrete Landscape Edging: A Step-by-Step Guide for Clean Lines for a fully set option.

Keep Roots and Trunk Safe

Avoid cutting through large roots when you dig. If you hit a root thicker than about 2 inches, reroute the trench around it rather than severing it. Never pile soil, mulch, or edging material against the trunk, and don’t bury the root flare, the slightly widened base where the trunk meets the soil. Mulch piled against bark invites rot and insects.

Consult a certified arborist before any digging if the tree is stressed, leaning, or especially old, since root damage can cause lasting decline.

Common Mistakes

  • Setting the edging too close to the trunk, which can damage roots and bark.
  • Installing shallow strips that heave out after the first freeze-thaw cycle.
  • Using too much mulch, which can suffocate roots and hold moisture against the bark.
  • Letting the edge sit above grade, where it catches mower blades and trimmer line.
  • Skipping stakes on curves, which causes the line to bow over time.

A flat spade with a sharp edge makes clean, straight trenches in most soils. Look for one with a long handle to reduce bending. View on Amazon

A rubber mallet drives stakes and seats strip edging without denting metal or bending the top edge. View on Amazon

A string trimmer with an edging guard helps keep the line crisp once the border is in place, especially along lawn-facing sides. View on Amazon

FAQ

How far from a tree should landscape edging go?

Most arborists suggest keeping the bed within the drip line and leaving a 2 to 3 inch mulch-free ring around the trunk. Larger trees can have wider beds, but avoid building up soil or edging against the trunk.

How deep should tree edging be installed?

Set most strip edging 4 to 6 inches deep so it resists heaving and root pressure. Pavers and stone need a compacted base instead of a simple trench.

Can landscape edging damage tree roots?

Digging through thick roots can harm the tree, so reroute the trench around any roots larger than about 2 inches. Shallow, careful installation outside the main root zone minimizes risk.

Conclusion

Good landscape edging for trees depends on planning the bed around the root zone, choosing material that suits your site, and installing it at the right depth. Keep the trunk clear, avoid cutting large roots, and check the border once or twice a year. A well-placed edge keeps the tree area tidy for years with very little upkeep.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our lawn edging & trimming guides, checking product details against manufacturer specifications and owner feedback.