Updated November 2026

Replacing the string on a Craftsman weed eater is a quick job once you know which line to buy and how the spool works. This guide walks you through choosing the right weed eater string for a Craftsman trimmer, loading it so it feeds properly, and avoiding the mistakes that cause jams and short line life. Most of the work takes under 15 minutes with basic tools.

Choose the Right Line Before You Start

Craftsman trimmers use a few different spool styles, so start by checking your owner’s manual or the label on the spool for the recommended line diameter. Manufacturers typically specify a diameter in inches, and common sizes for homeowner trimmers fall in the range of about 0.065 to 0.095 inch. Using line thicker than specified can overload the motor and cause the head to stall, while line that is too thin wears out quickly.

Pay attention to the line shape as well. Twisted or square-profile line tends to cut more aggressively, while round line is quieter and a good general choice. If you are also clearing thicker weeds, a larger diameter may be justified, but stay within the limit printed on your trimmer.

How to Load Craftsman Weed Eater String

Most Craftsman heads use either a bump-feed design or a pre-wound spool. Bump-feed heads let you tap the head on the ground to release a little more line, while pre-wound spools are installed as a unit. Always disconnect the spark plug wire or remove the battery before you touch the head.

  1. Remove the spool cover by pressing the tabs or turning the cover counterclockwise, depending on your model.
  2. Take out the old spool and clear any wound line or debris from the spool cavity.
  3. Cut a length of new line. Manufacturers commonly suggest about 10 to 20 feet, depending on the spool size, so check the figure printed on the spool or in the manual.
  4. Find the center of the line and insert it into the eyelet or slot that matches the spool’s winding direction. The arrow on the spool usually shows which way to wind.
  5. Wind the line evenly around the spool in the direction of the arrow, keeping the tension snug and the coils neat.
  6. Feed the free ends through the exit eyelets on the cover, leaving about 6 inches of tail on each side.
  7. Reattach the cover, pull the line ends to confirm they extend freely, and reconnect power.

Bump-Feed Heads

If your head is a bump-feed type, you do not need to wind the spool by hand. Insert the line through the eyelet, push the spool in, and tap the head against the ground while the engine is running to release more line as it wears.

Common Mistakes to Avoid

  • Winding the line against the arrow, which causes tangles and early breakage.
  • Leaving too much tail, which can strike the housing and snap off.
  • Using line heavier than the recommended diameter, which strains the motor.
  • Skipping the spark plug or battery disconnect before opening the head.
  • Forgetting to check the eyelets for trapped debris that can stop the line from feeding.

A simple set of tools makes the job faster and keeps your hands clear of the cutting head.

  • Replacement trimmer line matched to your spool: Choosing the diameter your manual specifies removes most guesswork at the store. View on Amazon
  • Replacement spool for your Craftsman model: A pre-wound spool saves time if winding by hand has been frustrating. View on Amazon
  • Work gloves: The cutting edges and line ends can be sharp when you handle the head. View on Amazon

If you are also checking other parts of your trimmer, the guide to Craftsman Weed Eater Accessories: A Guide to Choosing and Using the Right Ones covers related attachments, and 3 Best Weed Eater Craftsman Parts for Repairs and Replacements (2026) looks at common repair items. For a broader look at spool and head styles, see Weed Eater Echo Parts: How to Find, Identify and Replace the Right Ones, since many heads work on similar principles.

FAQ

What size weed eater string does a Craftsman need?

Check the diameter printed on your spool or listed in the owner’s manual, since Craftsman models vary. Using the specified size keeps the motor from overloading and helps the line feed properly.

Why does my Craftsman string keep breaking near the head?

This is often caused by line that is too thin for the work, a tail that is too long, or line wound against the spool arrow. Trim the tail to about 6 inches and confirm the winding direction.

Can I use any brand of trimmer line in a Craftsman?

Generally yes, as long as the diameter and head type match your manual’s specifications. Confirm the line fits the eyelets and spool cavity before you cut it to length.

Conclusion

Matching the line diameter to your Craftsman’s specifications and winding it in the direction the arrow shows will solve most loading problems. Keep the tail short, disconnect power before working on the head, and check the eyelets for debris. With those habits, your trimmer will feed reliably and cut cleanly through the season.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our lawn edging & trimming guides, checking product details against manufacturer specifications and owner feedback.