Updated November 2026
Dig in landscape edging by cutting a shallow, level trench along your marked line, setting the edging so its top sits just above grade, and backfilling firmly on both sides. Done correctly, the border holds its shape for years and keeps grass from creeping into beds. The steps below cover planning, digging, setting and finishing.
Plan the Line and Gather Your Tools
Lay a garden hose or spray paint along the edge you want, then step back and look at it from several angles. Smooth, sweeping curves read better than tight bends, and most edging looks cleanest when the radius stays at least 2 to 3 feet. Mark the line with landscape paint or stakes at 12-inch intervals so you can follow it without second-guessing.
Shopping for one? See our guide: 6 Best Easyflex No Dig Landscape Edging Kit Options for Clean Lines (2026).
You will need:
- A flat-bladed spade or edging spade
- A straight board and a 4-foot level
- A rubber mallet
- A tape measure and string line
- Crushed stone or sand for the base, if your edging calls for it
Cut the Trench to the Right Depth
Most dig-in edging sits in a trench about 2 to 3 inches deep, with the slot wide enough for the material’s thickness plus about half an inch on each side. Check your product’s instructions, since manufacturers specify depth based on the height of the piece. Slice straight down along the marked line with the spade, then lift the sod out in a clean strip. Keep the trench bottom level and remove any roots that would push the edging out of line.
Check Level as You Go
Set the board across the trench every few feet and place the level on top. Pack or scrape the bottom until the trench is consistent. A level base matters more than any other step, because an uneven trench creates waves in the border.
Set and Anchor the Edging
Lower the edging into the trench and press it firmly against the outer wall. Tap it down with the mallet until the top edge sits about three-quarters of an inch above the surrounding soil or turf line. This height keeps mower wheels from riding up over the edge while still giving a visible, finished line. On curves, make small adjustments as you go rather than forcing a long piece to bend.
Where sections meet, overlap or butt the ends tightly and check that they stay flush. If the material includes stakes or anchoring spikes, drive them through the holes at each joint and about every 18 to 24 inches along straight runs.
Backfill and Finish the Border
Pack soil or fine gravel against the inside and outside of the edging in layers, tamping as you go. Firm backfill prevents shifting when the ground freezes or after heavy rain. Once the border is set, water the surrounding area lightly and rake the grass edge so it meets the bed cleanly. Mulch the bed afterward to hide the seam and reduce weeds along the border.
Common Mistakes to Avoid
- Setting the edging too high, which catches mower decks and looks unnatural.
- Skipping the level check, leading to waves and gaps.
- Leaving loose soil behind the edging, which allows it to tilt over time.
- Cutting the trench too wide, so the piece wobbles instead of sitting snug.
- Digging when the ground is saturated, making clean cuts and firm backfill difficult.
Recommended Gear
A flat-edged spade makes clean vertical cuts and is the most useful single tool for this job.
A rubber mallet drives edging into the trench without cracking plastic or denting metal.
A 4-foot level lets you confirm the trench and the finished top line are consistent along the full run.
For more on specific systems, see Wood Landscape Timber Edging: A Step-by-Step Install Guide and What Are the Best Options for Landscape Edging? 7 Choices Compared. If you are choosing material first, Vigoro Metal Landscape Edging: A Step-by-Step Guide for Clean Lawn Borders walks through a metal install from start to finish.
FAQ
How deep should I dig for landscape edging?
Most dig-in edging needs a trench about 2 to 3 inches deep. Follow the manufacturer’s depth recommendation, since taller pieces may need a deeper cut.
Should the edging sit above or below the soil?
The top should sit about three-quarters of an inch above the surrounding soil or turf. This keeps mower wheels from riding over the border while still looking neat.
Can I dig in landscape edging on a curve?
Yes. Mark the curve with a hose, cut the trench in short sections, and bend the edging gently as you set it. Keep curves at least 2 to 3 feet in radius for the cleanest result.
Conclusion
Dig in landscape edging by planning the line, cutting a level trench and setting the material at the right height. Firm backfill and a neat grass edge finish the job. Take your time on the trench, since a clean base makes the rest of the work far easier.
