Updated November 2026

A dewalt weed eater string is easy to get right once you know two things: the line diameter your trimmer’s head accepts, and the way the spool is wound and loaded. This guide walks through choosing the correct line, measuring it, and loading it so your trimmer feeds smoothly and cuts cleanly. Most of the work takes about ten minutes.

Step 1: Check Your Trimmer Head and Line Specs

Start with the manufacturer’s information. DeWalt trimmers are sold in both corded and cordless models, and the spool each one uses differs. Look for the line diameter printed on the spool cap, in the owner’s manual, or on the head’s label. Common diameters for residential trimmers fall between 0.065 and 0.095 inch, and using a line thicker than the head rating can cause the motor to bog down or the head to bind.

Shopping for one? See our guide: 6 Best Weed Eater Gas Leaf Blower Combos for Yard Care (2026).

Also note the head type. Bump-feed heads advance line when you tap the head on the ground. Automatic heads release line on their own. Each has a spool design, and the line that fits one may not feed correctly in the other.

Step 2: Choose the Line Shape and Material

Trimmer line comes in round, square, twisted and multi-sided profiles. Round line is the most common and works well for general lawn edging. Square or twisted profiles tend to cut grass faster and hold up better in thick growth, though they can wear the spool hole if the fit is loose. Stick with the profile your manual recommends unless you have a specific reason to change.

Step 3: Load the Line Correctly

Once you have the right line, follow these steps:

  1. Disconnect the power or remove the battery before touching the head.
  2. Cut a length of line according to the length stated on the spool or in the manual. Many heads take roughly 15 to 20 feet total, split into two equal lengths.
  3. Find the arrow or direction mark on the spool and wind each line in that direction, keeping the lines evenly tensioned.
  4. Push the line ends into the eyelets or slots on the spool, leaving a few inches of tail.
  5. Reassemble the head, pull the line ends through the outlets, and then fit the cap.
  6. Run the trimmer briefly at idle to confirm the line feeds out evenly.

Step 4: Set the Right Cutting Length

Trim the line to the length the manufacturer specifies, usually about 5 to 6 inches beyond the cutting guard on cordless heads. Too long a line strains the motor and reduces cutting speed. Too short a line won’t reach the grass you need to cut, and the head will spin without making contact.

  • Replacement spool for your specific head matches the diameter and mounting your trimmer requires, so you avoid forcing the wrong spool into place. View on Amazon
  • Pre-cut trimmer line in the diameter your manual lists saves you measuring and gives you a consistent length for each reload. View on Amazon

Common mistakes

  • Using line thicker than the head rating, which strains the motor and can damage the drive.
  • Winding the two lines in opposite directions, which causes uneven feeding.
  • Forgetting to disconnect power before reloading.
  • Mixing bump-feed and automatic spools, since they are not interchangeable.
  • Letting the line run too long, which slows the head and wears the cutting guard.

If you’re working on a different trimmer setup, see Dewalt 20 Volt Weed Eater: Setup, Trimming Tips and Maintenance Guide for head and battery details. For other brands, Black and Decker Weed Eater String: How to Choose and Replace It (2026) and Craftsman Weed Trimmer String: How to Choose and Replace It for Clean Edges cover similar loading steps.

FAQ

What diameter string does a DeWalt weed eater use?

It depends on the model. Check the owner’s manual or the label on the spool cap, since the rated diameter is set by the head design.

Can I use a thicker line for tougher grass?

Not unless the manufacturer allows it. A line that’s too thick can overload the motor and damage the head.

How often should I replace the line?

Replace it when it runs out, breaks repeatedly, or becomes brittle and short. If you’re unsure about head damage or motor issues, consult a qualified small-engine or power tool service technician.

Conclusion

Matching the line diameter to your head, winding it in the marked direction and setting the correct length will cover most loading problems. Take a few minutes to confirm the specs before you start, and your trimmer will feed reliably and cut cleanly.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our lawn edging & trimming guides, checking product details against manufacturer specifications and owner feedback.