Updated November 2026

Replacing the line on a DeWalt 20V trimmer takes about five minutes once you know the process. You will remove the empty spool, cut fresh line to the correct length, wind it in the right direction and seat the spool so it feeds cleanly. The steps below apply to most DeWalt 20V string trimmers that use a bump-feed or fixed-line head, though the exact spool design varies by model.

Before You Start

Disconnect the battery first. A trimmer head can start spinning if the trigger is bumped during handling, and that is the most common avoidable injury during line work. Check your owner’s manual for the spool model number and the recommended line diameter, which is usually printed on the spool cap or in the manual.

Shopping for one? See our guide: 3 Best Dewalt String Trimmer 20vs (2026): Our Picks.

  • Battery removed from the tool
  • Replacement trimmer line matching the diameter in the manual (commonly around 0.065 inch for DeWalt 20V models)
  • Work gloves and safety glasses
  • A pair of sharp scissors or diagonal cutters

Removing the Old Spool

Press the tabs on the spool cap or turn the cap counterclockwise, depending on the head design, and lift off the cover. Pull out the spool and any remaining line. Clean debris, grass and dirt from the spool cavity with a small brush, since trapped grass can cause the new line to bind.

Winding and Loading the New Line

Cut two lengths of line that are each roughly 15 to 20 feet long. Find the center point of the first length and insert it into the anchor eyelet or slot on the spool. Wind the line evenly in the direction of the arrow printed on the spool, keeping the coils tight and flat so they do not overlap. Leave about 6 inches of free end on each side when you finish, then feed each end through the matching eyelet on the spool body.

Seating the Spool Correctly

Line that is wound unevenly will tangle or feed poorly, so keep the coil even as you work. Once the spool is wound, place it back in the head, set the cap in position and press or turn until it locks. Pull the free ends outward to confirm the line sits in the exit slots. Some heads have a small notch you can align with the arrow for accurate seating.

Testing and Final Adjustment

Reconnect the battery and start the trimmer outdoors, away from people and pets. Hold it at about waist height and let it run for a few seconds. If the line does not extend, tap the head lightly on the ground while the motor runs, which is the bump-feed action. If it still does not feed, the line may be wound in the wrong direction or caught on the spool, so remove the spool and check again.

Symptom Likely Cause Fix
Line will not feed Wound against spool arrow Rewind in the arrow direction
Line keeps breaking Wrong diameter or worn eyelet Match manual diameter; inspect eyelet
Head vibrates or wobbles Uneven coil or cap not seated Rewind evenly and reseat cap

Common Mistakes

  • Leaving the battery connected while working on the head.
  • Using line that is thicker than the manual specifies, which can overload the motor.
  • Winding the line loosely, which causes tangles and uneven feed.
  • Skipping the spool cleaning step, so debris blocks the new line.
  • Forgetting to wind in the arrow direction on the spool.

A pair of cut-resistant work gloves protects your hands when you handle sharp trimmer heads and cut line. View on Amazon

A small wire brush or stiff brush helps clear grass and dirt from the spool cavity before you load new line. View on Amazon

FAQ

How often should I replace trimmer line on a DeWalt 20V trimmer?

Replace the line whenever it runs short, frays or breaks at the eyelet. Frequent use on tough weeds or edges will wear it down faster than light trimming.

Can I use thicker line than the manual recommends?

It is better not to. Thicker line puts extra load on the motor and can reduce runtime and cause overheating. Stick with the diameter listed in your owner’s manual.

Why does my line keep retracting too far?

This usually happens when the line is wound too tightly or the spool is seated incorrectly. Rewind the line evenly and check that the cap locks fully. Consult your owner’s manual or a DeWalt service center if the problem continues.

Conclusion

With the battery disconnected, a clean spool and evenly wound line, a DeWalt 20V trimmer head can be reloaded in a few minutes. Match the line diameter to your manual and wind in the arrow direction, and the trimmer should feed reliably. For edge work, the Using a String Trimmer for Lawn Edges Safely guide covers technique that keeps your lines clean.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our lawn edging & trimming guides, checking product details against manufacturer specifications and owner feedback.