Updated November 2026
Ryobi string trimmer line replacement is a simple job once you know the spool design and the right line diameter. In this guide you will confirm what your trimmer needs, remove the old spool, wind and load fresh line, and test that the head feeds properly. Most owners can finish the job in about 10 to 15 minutes with basic tools.
Check Your Trimmer Before You Start
Ryobi trimmers use several head styles, and the spool is what changes most between models. Look at the head and the owner’s manual to identify your type, then confirm the line diameter the manufacturer specifies. Using a line that is too thick can overload the motor, while line that is too thin wears out quickly. If you are unsure which head you have, the Ryobi String Trimmer Line Replacement guide for beginners walks through the common designs. You can also read Ryobi Trimmer String Replacement: A Step-by-Step Guide for Beginners for a broader overview.
Shopping for one? See our guide: Top 7 Lawn Edger String Trimmer Combos for Clean Lines (2026).
Remove the Old Line and Spool
Disconnect the spark plug boot or remove the battery before touching the head, so the trimmer cannot start by accident. Then follow these steps:
- Press the tabs on the side of the head cover or twist it counterclockwise, depending on the model.
- Lift off the cover and the spring, if your model has one.
- Remove the spool and pull out any remaining line. Note how the line was wound and which way it entered the spool.
- Clean out grass, dirt and debris from the housing with a stiff brush or a rag.
Wind and Load the New Line
Cut a length of line that matches the spool’s documented capacity. Fold it at the midpoint, insert the loop into the spool’s anchor hole, and wind evenly in the direction marked on the spool. Keep the winding tight and even so the line does not tangle. Leave the ends at the exit holes according to the spool’s markings, then reassemble the head and pull the line out to the length marked on the housing.
Reinstall and Test
Put the spring and cover back on, seat the cover firmly, and reconnect power. Start the trimmer at low throttle and check that the line extends evenly on both sides. Let the engine or motor run briefly and confirm the line feeds when you tap the head on the ground.
Tools and Supplies You Need
| Item | Purpose |
|---|---|
| Replacement line in the diameter specified for your model | Cutting edge |
| Stiff brush or rag | Clearing debris from the head |
| Owner’s manual | Confirming head type and winding direction |
| Scissors or pruning shears | Cutting line to length |
Common Mistakes
- Installing line with the wrong diameter, which can strain the motor or cause poor cutting.
- Winding the spool in the wrong direction, so the line jams or does not feed.
- Leaving the spark plug connected or the battery installed while working on the head.
- Skipping debris cleanup, which can prevent the spool from turning freely.
- Pulling the line out too far, so it hits the housing and fails to feed.
Recommended Gear
A sturdy pair of work gloves helps protect your hands from sharp housing edges and cut line ends. View on Amazon
A small wire brush makes cleaning the head faster and more thorough. View on Amazon
FAQ
How often should I replace trimmer line?
Replace line when it becomes very short, frayed or brittle, or when it no longer feeds out on its own. Frequent use on tough weeds will wear it down faster.
Can I use any line diameter in my Ryobi trimmer?
No. Use the diameter listed in your owner’s manual or on the trimmer’s label. Heavier line can overload the motor and reduce performance.
What if the line keeps jamming after I reload it?
Check that you wound the spool in the marked direction and that the line ends sit in the correct exit holes. If problems continue, consult the owner’s manual or a qualified service technician.
Conclusion
With the right diameter, careful winding and a quick test run, Ryobi string trimmer line replacement takes only a few minutes. Keep the head clean and replace line before it gets too short to feed. Following the manufacturer’s instructions will keep your trimmer cutting cleanly all season.
