Updated November 2026

A string trimmer line for a Black and Decker trimmer comes down to three things: the line diameter your model accepts, the line shape, and how the spool is designed to hold it. Match those to your machine and you can reload in a few minutes and keep clean, even edges along walkways and fence lines. This guide walks through how to identify the right line and install it correctly.

Check Your Model Before You Buy String Trimmer Line

Black and Decker trimmers come in corded, cordless, and gas-assisted versions, and the spool system varies between them. Start by looking at the spool housing and the manual or label on the unit. Manufacturers usually specify a line diameter range, commonly somewhere between 0.065 and 0.095 inches depending on the model. Using line thicker than the rated size can overload the motor, while line that is too thin wears out quickly and may not cut tough weeds.

Shopping for one? See our guide: 3 Best Black and Decker Grass Trimmer String Options for Clean Lawn Edges (2026).

If you no longer have the manual, check the spool cap for a model number, then search the manufacturer’s support site for the specification sheet. Do not guess based on how the line looks on the spool.

Choose the Right Line Shape and Type

Most homeowners do well with round monofilament line, which is inexpensive and works for grass and light edging. Twisted or square-profile lines tend to cut more aggressively and hold their edge longer, which helps with thicker growth. Some lines include a built-in braided or co-polymer core for extra durability.

For edge work, you generally want a line that stays stiff enough to trim cleanly along concrete. A line that is too soft may bend and miss the lip of the sidewalk.

Load the Line Step by Step

Loading procedures differ by model, but most Black and Decker spools follow a similar pattern. Confirm the steps against your manual before you start.

  1. Disconnect the power source, remove the battery, or shut off and cool the engine.
  2. Press the spool release tabs or twist the cap counterclockwise to remove the spool cover.
  3. Take out any remaining line and wipe away debris from the spool housing.
  4. Cut a length of line to the length specified for your spool, often about 10 to 20 feet for a standard spool.
  5. Find the center of the line and wrap it around the spool in the direction marked by the arrow on the spool.
  6. Thread the two free ends through the eyelets or slots in the spool.
  7. Reattach the cover, pull the line ends out to the cutting length, and test the trimmer briefly before starting work.

Replace the Line Without Overloading the Head

Replacing line is a routine task, and the same steps apply each time. Keep a spare spool loaded so you can swap it in quickly during a long job. When you tap the trimmer head on the ground to advance line, you should hear and feel the line release. If the line does not feed, check that it is not tangled or wedged in the spool, and that the length is not too long for the housing.

Owners often report that line sticks when the spool is packed too full or wound loosely. Wind it firmly and evenly for smooth feeding.

Common mistakes

  • Using line diameter outside the rated range for your model.
  • Winding the line against the arrow on the spool, which prevents proper feeding.
  • Forgetting to disconnect power or remove the battery before reloading.
  • Cutting line too long, which causes jams and strain on the motor.
  • Running the trimmer with a partly loaded spool, which can cause uneven cutting.
  • A replacement spool for your specific Black and Decker model keeps you from relying on a line size that may not fit. View on Amazon
  • Pre-cut trimmer line in the diameter listed in your manual saves measuring and reduces waste. View on Amazon

For related setup help, see Black and Decker Weed Eater String: How to Choose and Replace It (2026) and Using a String Trimmer for Lawn Edges Safely.

FAQ

What size string trimmer line fits a Black and Decker trimmer?

Check the manual or the label on the trimmer for the rated diameter range. Using line within that range helps protect the motor and keeps the line feeding properly.

How often should I replace trimmer line?

Replace it when the line is worn short, frayed, or no longer feeds when you tap the head. Frequent use on tough weeds or edges will wear line out faster.

Can I use any brand of line in a Black and Decker trimmer?

You can usually use other brands as long as the diameter, shape, and length match your spool and model. Confirm the specifications in your manual before buying.

Conclusion

Matching the line diameter and shape to your Black and Decker model is the key step. Load the spool carefully, follow the winding direction, and keep a spare spool ready. With the right line, your edges will stay cleaner and your trimmer will run more smoothly.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our lawn edging & trimming guides, checking product details against manufacturer specifications and owner feedback.