Updated November 2026
A string trimmer Cub Cadet model is simple to keep cutting well once you know three things: how to load the right line, how to wind it so it feeds correctly, and how to spot the wear that makes a trimmer bog down. This guide walks through each step so you can get a clean, even edge without guessing.
Check the Trimmer Before You Touch the Line
Start by confirming the trimmer is switched off and, for gas models, that the spark plug wire is disconnected. Look at the head and the spool housing for cracks, and make sure the bump feed or auto-feed mechanism moves freely. A stuck head will cause line to break or tangle no matter how carefully you wind it.
Shopping for one? See our guide: Top 7 Lawn Edger String Trimmer Combos for Clean Lines (2026).
How to Load Cub Cadet Trimmer String
Most Cub Cadet trimmer heads use a dual-line spool, and the exact method depends on the head design. Owners’ manuals and the labeling on the spool housing list the recommended line diameter, which is the number to match when you buy replacement line. Using a line that is too thick can overload the motor, while line that is too thin wears out quickly.
- Remove the spool cover and take out the old spool, noting how the line was wound.
- Cut two equal lengths of new line, usually in the range the manufacturer specifies for your head.
- Thread each line through its eyelet and follow the arrow markings on the spool to find the winding direction.
- Wind each line evenly in the same direction until about 4 to 6 inches remain free at each end.
- Insert the free ends into the correct slots, then reinstall the spool and cover.
- Pull the free ends outward until the line feeds, then start the engine or motor and test briefly.
Winding Direction Matters
If the line winds against the arrow, it will tangle and may not advance when you tap the head. Take a moment to confirm the direction before you close the housing.
Replace Line Before It Stops Cutting
Line that has worn down to a short stub, or has become brittle from heat and sun, will fail to cut grass cleanly and can break at the eyelet. Check the length each time you use the trimmer. Many owners find that replacing the full spool every few uses keeps performance steady, though frequency depends on how much grass you cut and how dense it is.
| Symptom | Likely cause | Fix |
|---|---|---|
| Line won’t feed when tapped | Line is too short or wound backward | Rewind in the arrow direction |
| Line breaks at the head | Brittle or wrong diameter | Replace with the specified diameter |
| Motor bogs down | Line too thick or heavy grass buildup | Downsize line and clear the guard |
Keep the Head Clean for Better Edges
Wrapped grass and debris around the spool housing reduce the amount of line that can feed and can stop the head from rotating freely. Clear the area after each session and check the guard. For edge work, an accurate tool for the job matters as much as the line itself. If you are weighing options, Using a String Trimmer for Lawn Edges Safely covers technique and safety, and Lawn Edger vs String Trimmer: Which Gives Cleaner Lawn Edges? compares results with a dedicated edger.
Common Mistakes to Avoid
- Using line that does not match the diameter in the manual.
- Winding the spool unevenly, which causes the head to wobble.
- Letting line run very short before replacing it.
- Cutting with the trimmer held too high, which wastes line and strains the motor.
- Skipping the cleanup of wrapped grass around the head.
Recommended gear
A line of the correct diameter is the most important accessory for any Cub Cadet trimmer. Look for the diameter printed on the spool or in the manual when you shop.
- Replacement trimmer line in the diameter your head specifies, since mismatched line causes most feed problems. View on Amazon
- A pair of gloves for handling the head and wrapped grass, which keeps your hands clear of sharp line ends. View on Amazon
FAQ
What line size does a Cub Cadet string trimmer use?
The correct diameter is listed in the owner’s manual and often printed on the spool housing. Always use the size the manufacturer specifies, since a thicker line can overload the motor.
How often should I replace trimmer line?
Replace it when the line is worn to a short stub, becomes brittle, or fails to feed when you tap the head. Frequency depends on how much you cut and how dense the grass is.
Why won’t my trimmer line feed?
The most common reasons are line that is too short or wound against the arrow direction on the spool. Rewind the line in the correct direction and check that the free ends are seated in the slots.
Conclusion
With the right diameter, an even winding direction and regular cleanup, a string trimmer Cub Cadet model will hold a clean edge session after session. Check the line each time you use the tool and replace it before it runs short. For specific parts and repair questions, consult the manufacturer or a qualified small-engine technician.
