Updated November 2026
Landscape edging on slope areas takes a bit more planning than flat ground, but the result is worth it. This guide shows you how to measure the grade, choose an edging system that holds its position, and set it so the border stays straight and the soil stays where it belongs. The same approach works for landscape edging for slopes, whether you are working with a gentle incline or a steep bank.
Assess the Slope Before You Buy Anything
Start by measuring how much the ground drops over the length of your bed. Lay a 4-foot level along the line you plan to edge, and use a tape to measure the gap at the low end. A rise of 1 inch over 4 feet is a mild grade. Anything beyond 3 inches over 4 feet is steep enough that a single-piece edging strip will tend to tilt or pull away from the soil.
Shopping for one? See our guide: 6 Best Easyflex No Dig Landscape Edging Kit Options for Clean Lines (2026).
Note where water runs during heavy rain. Edging acts as a dam, so water pooling behind it can wash soil out underneath. If you see a clear runoff channel, plan to add a small gap or weep point every few feet, or use a stone border that lets water pass.
Choose an Edging System That Fits the Grade
On gentle slopes, steel or aluminum strips driven into the soil with stakes work well because they follow the contour without much bending. On steeper grades, stacked stone or timber borders with a level base course are more stable, since each unit sits on its own footing rather than relying on a long, continuous strip.
For a broader comparison of materials, see What Are the Best Options for Landscape Edging? 7 Choices Compared. If you prefer a stake-and-strip system, Spikes for Landscape Edging: A Step-by-Step Guide to Clean Lines explains how to space and angle the stakes for a solid hold.
Install Edging on a Slope in Five Steps
- Mark the line. Use a garden hose or marking paint to lay out the curve. On slopes, keep curves gentle so the edging does not have to bend sharply.
- Dig a trench on the high side. Cut a trench about the depth of the edging plus 1 inch. Work from the top of the slope downward, so each section can be checked against the one above it.
- Step the base on the low side. Where the grade drops, dig the trench in short level steps rather than one continuous slope. Each step should be no more than about 12 inches long. This keeps the top edge of each piece even.
- Set the edging and check level. Place each section, check it with a level, and drive stakes every 12 to 18 inches on the downhill side, angled slightly toward the bed.
- Backfill and tamp. Fill behind the edging with soil or a compacted base of crushed stone, then tamp in layers. Finish by checking the top line from one end to the other.
Measurements That Matter on a Slope
| Slope (rise per 4 ft) | Recommended approach | Stake spacing |
|---|---|---|
| Under 1 inch | Standard strip edging, straight install | 18 inches |
| 1 to 3 inches | Strip edging with stepped trench | 12 to 18 inches |
| Over 3 inches | Stacked stone or timber with compacted base | Per manufacturer; use base course |
Recommended gear
A 4-foot level and a hand tamper make the stepped trench much easier to keep even. View on Amazon
A half-moon edging spade gives you a clean vertical cut, which helps the edging sit flush against the soil. View on Amazon
Common Mistakes to Avoid
- Installing one long strip across the whole slope, which causes the top to lift and the bottom to sink.
- Skipping drainage gaps where water collects, leading to washout behind the border.
- Staking only at the ends instead of every 12 to 18 inches on the downhill side.
- Backfilling without tamping, which leaves air pockets that settle later.
- Edging the bed before grading the soil behind it, so the border sits too high.
FAQ
Can I use plastic edging on a steep slope?
Flexible plastic is hard to keep level on steep grades and often shifts with freeze-thaw cycles. Stacked stone or timber with a compacted base is generally more reliable on slopes over 3 inches per 4 feet.
How deep should slope edging be set?
Most strip edging should sit with about 2 to 3 inches above grade and the rest below. Bury the bottom edge at least 1 inch to keep it from being pushed out by soil movement.
Do I need a retaining wall instead of edging?
If the bed holds back soil more than about 6 inches high, a retaining wall is the safer choice. Edging is designed to define a border, not to hold back significant soil pressure.
Conclusion
Landscape edging on a slope works best when you measure the grade first, step the trench to follow the contour, and stake the downhill side firmly. Match the material to the amount of slope, and leave room for drainage where water collects. Done this way, your borders will stay crisp season after season.
