Updated November 2026
Stringing an Echo weed eater means feeding a fresh length of trimmer line into the spool so it cuts cleanly and advances when you tap the head. Once you know the order of steps, the whole job usually takes about 10 minutes. This guide covers what you need, how to wind the line correctly, and how to check your work before you start trimming.
What You Need Before You Start
Gather everything first so you are not stopping halfway through. Most Echo trimmers use a bump-feed head, and the spool and line size are specified in your owner’s manual.
Shopping for one? See our guide: Echo or Stihl Weed Eater (2026): Which Is Better for Your Yard?.
- Replacement trimmer line in the diameter your manual specifies (commonly around 0.065 inch for homeowner models)
- Scissors or a utility knife
- A flat surface and a clean rag
- The owner’s manual, for the correct line diameter and head model
Using line that is too thin will feed too easily, while line that is too thick can strain the motor and cause the head to jam. If you have lost the manual, check the model plate on the shaft or the Echo website for your model number.
Step-by-Step: Winding the Line onto the Spool
- Disconnect the spark plug boot or remove the battery so the trimmer cannot start while you work.
- Remove the trimmer head by pressing the tabs or removing the retaining cap, then take out the old spool and clear any leftover line.
- Cut two lengths of line to the length printed on the spool or shown in the manual, usually a little under 20 feet for each side. Cutting two equal pieces lets you load both chambers evenly.
- Find the center point of each line and insert it into the anchor hole or slot on the spool. Leave a few inches free on each end.
- Wind in the direction arrow printed on the spool. Keep the lines tight and even, and wind neatly so the coils do not cross or overlap.
- Secure the tail ends in the eyelets on the spool or spool cover, leaving about 6 inches of line sticking out.
- Reassemble the head by setting the spool back in the housing and attaching the cover.
- Feed the line through the eyelets on the housing, pulling each tail out until it is evenly exposed.
Testing the Feed and Setting the Cutting Length
Reconnect the spark plug or battery and start the engine at idle. Engage the throttle briefly and check that the line extends. If it does not, tap the head firmly on the ground while the engine is running at low speed. Bump feed works only when the head is spinning, so the line will not come out on its own.
Keep the cut length near the length the manufacturer specifies. Longer line cuts more aggressively but puts more load on the engine, so trim it only as long as needed. Clear any excess with the blade guard or a cutting edge rather than wrapping the line around the guard.
Common Mistakes to Avoid
- Winding the line in the wrong direction, which can cause the head to feed poorly or not at all.
- Using line that is too thick for the head, which can damage the gearbox or drive shaft.
- Forgetting to disconnect the spark plug or battery before opening the head.
- Leaving the two tail ends uneven, which causes unbalanced cutting and vibration.
- Overloading the spool. Most spools hold only a set length, and too much line will prevent the head from closing properly.
Recommended Gear
A few inexpensive items make the job easier and help you keep the line tidy.
- Echo-compatible trimmer line in the diameter your manual lists. Matching the line size to your head prevents feeding problems and extends engine life. View on Amazon
- A small pair of sharp scissors. Clean cuts make it easier to seat the line in the spool anchor. View on Amazon
- A spare spool cap or head for quick swaps. Having a second head lets you restring at your leisure rather than mid-job. View on Amazon
FAQ
How much line should I load into an Echo weed eater?
Load the length printed on the spool or listed in your manual, which is typically about 20 feet per side on many homeowner models. Overloading prevents the head from closing properly.
Why won’t my Echo trimmer feed line when I tap the head?
Bump feed only works when the engine is running and the head is spinning. Check that the line is wound in the correct direction and that the tails are seated in the eyelets.
Can I use a different line diameter than the one in my manual?
It is best to stick with the diameter your manual specifies. A line that is too thick can strain the engine and cause the head to jam, while a line that is too thin may not cut well. If you are unsure, check the owner’s manual or ask a qualified outdoor power equipment dealer.
Conclusion
Stringing an Echo weed eater is a simple process once you have the right line, wind it in the direction marked on the spool, and test the feed before you start cutting. Following these steps should keep your trimmer running cleanly through the season. If your head or spool is damaged, replacing it is usually faster than repairing it.
