Updated November 2026

Worx string trimmer parts are easier to match than most people expect once you know where the model number is printed and which components wear out first. This guide shows you how to identify your trimmer, locate the correct replacement part, and install it so the trimmer cuts cleanly again. Most owners only need to replace a spool, a cutting head, or a guard, and each job takes about 10 to 20 minutes with basic tools.

Identify Your Worx Trimmer Model First

Parts are model-specific, so start by finding the model and serial number on the label, usually on the motor housing or the shaft near the handle. Write both numbers down before you search for anything. Worx has produced several trimmer lines over the years, and a spool that fits one model may not fit another even when the head looks identical. Owners often report that a quick photo of the label saves a return trip to the store.

Shopping for one? See our guide: Top 7 Lawn Edger String Trimmer Combos for Clean Lines (2026).

Diagnose Which Part Needs Replacing

Before you buy anything, confirm the part that’s failing. A trimmer that won’t feed line is usually a spool or line problem, while one that vibrates or cuts unevenly may have a bent shaft or damaged cutting head. Check these common wear points:

  • Spool and cap: cracked tabs, worn bump-feed mechanism, or a cap that won’t seat.
  • Cutting head: stripped threads or a housing that no longer holds the spool.
  • Guard: cracks or loose mounting screws that let debris strike you.
  • Shaft and drive housing: bends or play that causes rattling. These are less common and often need professional help.

Find and Order the Correct Replacement

Once you know the model and the failed component, look for a part listed for your exact model. Compare the part number on the old component with the listing, and check the dimensions if the part is a spool or head. Avoid universal-fit spools unless the packaging explicitly states compatibility with your model, since a loose fit can cause the spool to fly off during use. Manufacturers specify exact compatibility for a reason, so trust their listings over guesswork.

  1. Note the model and serial number from the label.
  2. Compare the old part against the product photos and part numbers.
  3. Order the matching component and keep your receipt in case of a mismatch.

Replace the Spool or Cutting Head Step by Step

Always disconnect the power source before touching the cutting head. For battery models, remove the battery. For corded models, unplug the tool. Then:

  1. Press the spool release tabs or unscrew the cap, depending on your head design.
  2. Remove the old spool and clean out any wound line or debris from the housing.
  3. Insert the new spool and make sure it seats fully and sits flush.
  4. Reattach the cap and confirm the head turns freely without wobbling.
  5. Thread the line through the eyelets as the manual specifies, then test by running the trimmer briefly at low speed.

If the head still wobbles after reassembly, the housing or drive shaft may be damaged, and that’s worth a closer look before you run the tool at full speed.

Common Mistakes to Avoid

  • Buying a part without checking the model and serial number first.
  • Running the trimmer with a cracked guard or loose screws.
  • Overtightening the cap, which can crack plastic threads.
  • Forcing a spool that doesn’t seat, instead of confirming the fit.
  • Skipping the power disconnect before working on the head.
  • A small set of hex keys and screwdrivers: useful for guard screws and cap fasteners without stripping them. View on Amazon
  • Replacement trimmer line: the correct diameter and type for your head keeps feeding reliable. View on Amazon

For more background, see Ryobi Trimmer String Replacement: A Step-by-Step Guide for Beginners and Using a String Trimmer for Lawn Edges Safely, which cover line loading and safe edging practices.

FAQ

Can I use a spool from a different Worx model?

Only if the listing explicitly confirms compatibility with your model. Spools that look similar can differ in diameter, tab design, or bump mechanism, so check the model number before installing.

How do I know if the cutting head or the spool is worn?

If the line won’t feed or the spool cap won’t seat, the spool is the likely culprit. If the head wobbles or the housing has cracks, the cutting head itself needs attention.

Should I have a professional repair a bent shaft?

Yes. A bent shaft or drive housing problem can be dangerous to fix improperly, so consult a qualified small-engine or power-tool repair professional if you notice vibration or play in the shaft.

Conclusion

Finding the right worx string trimmer parts comes down to identifying your model, diagnosing the failed component, and matching the part number exactly. Most spool and head swaps take only a few minutes once the correct part is in hand. Keep your model number handy, and your trimmer will be back to clean, consistent cutting.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our lawn edging & trimming guides, checking product details against manufacturer specifications and owner feedback.