Updated November 2026

L shaped landscape edging wraps a bed or lawn along two straight sides that meet at a sharp inside corner. Done right, it gives you crisp lines, a clean transition between turf and mulch, and a border that holds its shape for years. This guide covers layout, cutting, setting, and corner joins so you can finish the job in a single weekend.

Plan the Layout Before You Cut Anything

Start by marking the outside edge of the bed with a garden hose or landscape paint. Walk the shape from a few feet back to check that the curves and corners look intentional. An L shape has one outside corner and one inside corner, and both need to read as deliberate. Measure each straight run and write it down, then add about 2 inches to each length to allow for overlap at the joints.

Shopping for one? See our guide: 6 Best Easyflex No Dig Landscape Edging Kit Options for Clean Lines (2026).

Gather Materials and Set the Corner Joints

Most L-shaped runs use two pieces of edging joined at a 90-degree angle. Check that the edging system you chose includes corner connectors or stakes rated for the material. Plan to set a stake within 6 inches of every joint and roughly every 3 feet along straight runs. Before digging, confirm the path is clear of utility lines by calling 811 in the United States.

  1. Mark the outline with a hose or spray paint.
  2. Measure each straight segment and add 2 inches for overlap.
  3. Cut the edging to length using a miter saw or metal shears, depending on material.
  4. Dig a trench along the marked line, about 1 inch deeper than the edging height.
  5. Set the edging in the trench, starting at the outside corner.
  6. Join the inside corner with a connector or by butting the ends tightly.
  7. Drive stakes at each joint and every 3 feet, leaving the top just below the edging rim.
  8. Check the top edge with a level and adjust the depth as needed.
  9. Backfill the trench and tamp the soil firmly against the outside face.

Handle the Inside Corner Without Gaps

The inside corner is where most L-shaped projects go wrong. When two straight pieces meet, the inside edge often leaves a small notch. To avoid this, cut one piece with a 45-degree miter so the ends overlap cleanly, or use a manufactured corner piece sized for your profile. Press the joint together and check that the top rim stays level across the junction before staking it.

Check Alignment Across the Joint

Sight along the top of the edging from one end to the other. Any dip or bump at the corner will be obvious in the finished bed. Lift or lower the joint section by adding or removing soil underneath until the line is smooth.

Finish the Border and Maintain Clean Lines

Once the edging is set, fill the bed with mulch or soil to within about 1 inch of the top rim. This keeps material from spilling over and makes trimming easier later. Trim the grass along the outside face with a string trimmer or half-moon edger, and run the blade along the top of the edging to keep the line sharp through the season.

Common Mistakes

  • Skipping the trench, which leaves the edging sitting on top and prone to heaving.
  • Placing stakes too far apart, which lets corners shift after rain or mowing.
  • Cutting corner pieces square instead of mitering, causing visible gaps.
  • Backfilling without tamping, which creates soft spots that sag over time.
  • Forgetting to level the top edge before final backfill.

A reliable tape measure and a sturdy level make the layout and check steps far more accurate. View on Amazon

A hand tamper packs the backfill evenly so the edging does not settle unevenly after the first few weeks. View on Amazon

A miter saw or metal-cutting blade handles the angled cuts needed for a tight inside corner. View on Amazon

FAQ

How deep should I set L shaped landscape edging?

Bury the bottom of the edging about 1 inch deeper than the trench you dig, so the top sits at the height you want. Most manufacturers recommend setting at least a few inches below grade for stability.

Can I join the two straight sections without a connector?

Yes, you can butt the ends together with a 45-degree miter cut and secure the joint with a stake placed directly beside it. Connectors make the joint stronger but are not strictly required.

How far apart should stakes be on an L-shaped border?

Place a stake at every joint and roughly every 3 feet along straight runs. Closer spacing helps on curves and in soft soil.

Conclusion

A clean L shape comes down to accurate layout, a level trench, and a tight inside corner. Take time at the joints and stake carefully, and the border will stay sharp for seasons. For more options on materials and setup, browse our What Are the Best Options for Landscape Edging? 7 Choices Compared comparison.

Caleb Morgan

About Caleb Morgan

Caleb Morgan is part of our editorial team and reviews and edits our lawn edging & trimming guides, checking product details against manufacturer specifications and owner feedback.