Updated November 2026
Ryobi trimmer string replacement is a quick job once you know the spool layout. You will unplug or disconnect the trimmer, remove the spool, cut and wind fresh line in the correct direction, and feed the ends through the eyelets. Most owners finish in under ten minutes with basic tools and the right line.
Before You Start: Check Your Trimmer and Line
Ryobi makes several trimmer heads, so confirm which one you have before buying line. Look at the spool cover: a bump-feed head usually has a tap-to-advance button, while a fixed-line head has no moving parts beyond the spool. Check the manual or the label on the shaft for the recommended line diameter, which is commonly listed in the range of 0.065 to 0.080 inches for consumer models. Using line that is too thick can overload the motor, and line that is too thin will wear out quickly.
Shopping for one? See our guide: Top 7 Lawn Edger String Trimmer Combos for Clean Lines (2026).
For a broader look at line choices, see Weed Eater String Craftsman: How to Load the Right Line (Step by Step) and Black and Decker Weed Eater String: How to Choose and Replace It (2026). A related read: Best Cordless String Trimmers.
Step-by-Step Ryobi Trimmer String Replacement
- Disconnect power. Remove the battery from a cordless model or unplug an electric one.
- Press the spool tabs or twist the cover counterclockwise to remove the spool cover.
- Take out the old spool and remove any remaining line. Note the direction the line was wound.
- Cut a length of new line, typically about 15 to 20 feet, depending on your spool capacity. Fold it at the midpoint.
- Hook the midpoint into the notch or anchor on the spool core, then wind both strands in the same direction the old line was wound, usually clockwise as viewed from the top.
- Leave about 6 inches of each end free and thread them through the eyelets in the spool, following the arrows molded into the spool.
- Reinstall the spool, reattach the cover, and pull the line ends to advance it.
- Reconnect power, run the trimmer briefly, and check that the line feeds out evenly.
Tips for Clean Winding
Keep the line taut as you wind so it does not tangle or cross over itself. If the spool has a line guide or channel, seat each loop inside it. Uneven winding causes the head to vibrate and the line to break early.
Choosing the Right Replacement Line
Match the diameter and shape to your model. Round line suits general lawn trimming, while square or twisted profiles cut grass and light weeds more aggressively. Pre-cut replacement line packs are convenient, but bulk line lets you refill the spool more often.
| Line Type | Best For |
|---|---|
| Round, 0.065 in. | Light grass and edging around beds |
| Round, 0.080 in. | Thicker grass and general trimming |
| Square or twisted | Dense weeds and tougher growth |
Common Mistakes to Avoid
- Winding in the wrong direction, which prevents the line from feeding out.
- Using line diameter outside the manufacturer’s recommended range.
- Leaving the battery connected while working near the head.
- Forgetting to thread both ends through the eyelets before reinstalling.
- Overfilling the spool so the cover will not seat.
Recommended Gear
- Ryobi replacement spool and line kit: A spool designed for your head keeps the fit and feed correct. View on Amazon
- Round trimmer line in the correct diameter: Matching the gauge your manual specifies protects the motor and gives a clean cut. View on Amazon
- Snips or a utility knife: Clean, square cuts make threading easier. View on Amazon
FAQ
How often should I replace trimmer line?
Replace it whenever the spool runs empty or the line becomes too short to cut effectively. Frequent use on thick growth means more frequent refills.
Can I use any trimmer line in my Ryobi?
Only use line that matches the diameter range in your manual. Oversized line can strain the motor and damage the head.
Why does my trimmer not feed line after I reload it?
The most common cause is winding in the wrong direction or threading the ends incorrectly through the eyelets. Reopen the spool and check the arrow direction.
Conclusion
Ryobi trimmer string replacement becomes routine once you know your head type and line diameter. Wind neatly, thread both ends through the eyelets, and test the feed before you start cutting. With these steps, your edges will stay sharp and your trimmer will run smoothly through the season.
