Updated November 2026
Ryobi weed trimmer string replacement takes about five to ten minutes once you know the steps. You will remove the empty spool, wind fresh line in the correct direction, and feed the ends through the eyelets so the head spins without wobbling. The process is nearly the same for most Ryobi string trimmers, though the spool design varies by model.
Gather the Right Supplies Before You Start
Check your trimmer’s manual for the recommended line diameter, which is usually printed on the spool or the head housing. Most Ryobi models use line in the range of .065 to .080 inch, and using a line that is too thick can strain the motor. Have a pair of scissors or a utility knife ready, and disconnect the spark plug boot on gas models or remove the battery on cordless models before you touch the head.
Shopping for one? See our guide: 3 Best Craftsman String Trimmer Replacement Heads (2026).
Remove the Old Spool and Clean the Housing
- Lay the trimmer flat and press the tabs on the head cover, or turn the cover counterclockwise to release it, depending on your model.
- Lift off the cover and the spool. Some Ryobi heads use a bump-feed design, while others use a fixed-line spool.
- Pull out any remaining line and wipe away grass, dirt and debris from the spool cavity. Debris can make the head bind or throw off the balance.
- Inspect the spring and the eyelets. Replace any spring that looks stretched or corroded.
Wind and Load the New Line
Winding the Spool
Cut two lengths of line roughly 15 feet each, or the length listed on the spool packaging. Fold the line at its midpoint and hook the loop onto the center post of the spool. Wind each strand evenly in the direction indicated by the arrow on the spool, keeping the coils tight and flat. Leave about 6 to 8 inches of tail at each end. If you want more background, see Natural Replacement for Roundup Weed Killer: A Step-by-Step Guide (2026).
Threading the Eyelets
Push one tail through the first eyelet and pull it out through the second eyelet, following the molded channels on the spool. Repeat with the other tail. Make sure the line exits from both sides of the head, pulling roughly equal amounts to keep the trimmer balanced.
Reinstall the Head and Test the Trimmer
Seat the spool back into the housing, lock the cover in place, and tug the line ends to confirm the spool is secure. Reconnect the spark plug boot or battery, then run the trimmer briefly at idle. The head should spin smoothly. If it vibrates, stop, remove the spool, and check that the line is wound evenly.
| Symptom | Likely Cause | Fix |
|---|---|---|
| Head wobbles at full speed | Uneven winding or unbalanced line lengths | Rewind evenly and trim both tails to the same length |
| Line does not feed out | Line stuck in the spool or wound the wrong direction | Remove the spool and rewind following the arrow |
| Line breaks right at the eyelet | Line too thin or eyelet worn | Use the recommended diameter and inspect the eyelet |
Common Mistakes to Avoid
- Winding the line against the arrow, which keeps it from feeding out.
- Using line that is thicker than the manufacturer specifies, which can damage the drive shaft.
- Leaving the spark plug connected while you work on a gas model.
- Forgetting to clean the spool cavity, leading to vibration and early wear.
- Uneven tail lengths, which throw the head out of balance.
Recommended Gear
- Ryobi replacement trimmer line: Matching the manufacturer’s diameter and format helps the spool feed properly. View on Amazon
- Replacement spool for Ryobi string trimmer: A prewound spool saves time and eliminates winding errors on heads that are hard to load by hand. View on Amazon
If you are new to trimmer maintenance, read Ryobi Trimmer String Replacement: A Step-by-Step Guide for Beginners for a slightly different walkthrough. Owners of Ryobi gas models may also find Gas Ryobi Weed Eater: How to Start, Trim and Maintain It Right useful for general upkeep.
FAQ
How often should I replace the trimmer line?
Replace it whenever the line runs out or breaks frequently at the eyelet. Heavy use on thick weeds wears line faster than light trimming along edges.
Can I use any string in my Ryobi trimmer?
No. Use line that matches the diameter and spool type listed in your owner’s manual. Mismatched line can cause feeding problems and strain the motor.
What if the line keeps jamming in the head?
Remove the spool, check for tangled or stuck line, and confirm the tails are the correct length. Rewind the spool evenly and make sure the line exits both eyelets freely.
Conclusion
Ryobi weed trimmer string replacement is manageable with a clean workspace, the correct line diameter, and careful winding in the arrow’s direction. Take the time to balance the tails and test the head before you start trimming. With regular replacement and cleaning, your trimmer will keep producing crisp edges along walkways and beds.
